500W Fog Machine With 3 RGB LED and Remote Control
14 Colorful LED Lights Effect
Individual control of the LED color and individual control of smoke spraying.
Use Steps
【Step 1】Pour the atomized liquid into the tank, ensure the tube is at the bottom, and ensure the metal nozzle is fully immersed in the atomized liquid.
【Step 2】Install the power cable and turn it on to heat the fog machine. The indicator lamp will not be on while preheating. (Built-in remote receiver).
【Step 3】Wait the fog machine to heat up for 2-3 minutes until the red light is on. To spray smoke, control the machine with a remote control.
The effective range is within 15m/49ft without any barrier
You can hang the machine on the high spot so it can spray fog downwards.
The handle can be installed as a holder to keep the machine spraying upwards.
Widely used:
Colorful stage effects for DJ, ballroom, party, disco, theater, wedding, church, special event, Christmas, and home party lighting.
Detail：
Equipped with a remote control
Packing list:
Fog Machine *1
Handle *1
Power Cable *1
Screws for Handle *2
Remote Control *1
Instruction Manual *1
Safety precautions:
1. Attention: improper placement of the battery may cause an explosion. Replace only the same or equivalent types.
2. Warning on the battery of the controller: the used battery should not be discarded with domestic garbage but should be recycled at a separate collection point. Improper battery replacement may cause an explosion. Keep new and old batteries out of children's reach. If the battery compartment is not properly closed, please stop using it and put it out of the reach of children. Warning: The provided force controller contains button cells. If swallowed, it may cause serious internal burns or even death within 2 hours.
3. If you have any questions about whether the battery has been swallowed or introduced into other parts of the body, please contact the doctor immediately. Before cleaning the equipment, if it is connected to the power supply, please disconnect it. Do not use harsh cleaners. Use a clean cloth to remove dust or dirt from the product. We are not responsible for damage caused by improper handling, improper use, or wear. We reserve the right to make technical modifications.
4. To protect the environment and/or human health, waste should be recycled responsibly to support the sustainable reuse of resources. If you need to recycle second-hand electrical appliances, please go to the electrical appliance collection center or contact the dealer who purchased your products. They will ensure that products are recycled ecologically.
Pay special attention to:
1. This product is in a heated state during use. The high temperature of the machine is normal; please do not touch it with your hands.
2. This product should be used in a dry place. Any liquid should not penetrate the inside of the machine (just the oil bottle). If accidental infiltration occurs, turn off the power immediately and wait for the machine to dry before using it.
3. Keep away from flammable and explosive materials when using this product.
4. When the liquid in the oil bottle is about to run out, smoke fluid should be added immediately; otherwise, continuing to work will damage the machine.
5. When the machine is working, please do not directly touch the smoke vent or the bottom of the machine with your hands. To prevent burns.
6. After use, it should be packaged and stored after it has cooled down.
7. Turn off the machine when no one is present.
Other Precautions:
1. All sprayers will produce a small amount of mist or moisture around the nozzle, and occasionally a small amount of smoke will be emitted when it is stopped, which is a normal phenomenon.
2. The machine has a working mode of heating and cooling. The machine can only start spraying once the heating is complete.
3. Regular cleaning is very beneficial for the machine. Poorly atomized liquid will cause clogging. It is recommended to use a high-quality atomized liquid.
About machine maintenance:
1. After about 40 hours of continuous use, please use 80% distilled water and 20% white vinegar to remove the impurities accumulated in the heat pipe.
2. Clean the pipeline and filter head in the tank; 3. Pour out the mist liquid and replace the cleaning liquid (80% distilled water and 20% white vinegar).
4. Turn on the power, continue heating, and use the cleaning fluid instead of the smoke fluid to work until the cleaning fluid is used up.
5. If the smoke becomes smaller, the pump makes a noise or cannot spray. Turn the power off immediately, and check to see if there is smoke fluid in the oil bottle. Whether the fuse is intact or whether the controller interface and power plug are plugged in, if all of these are normal, please connect the power and plug to try again. If the problem still cannot be solved, please contact us, and we will help you solve it as soon as possible.
Reviews
There are no reviews yet.
Be the first to review “Somspot LED Colorful Smoke Machine Remote Fogger Ejector Fog Machine for DJ Disco KTV Party Wedding Bar Club Stage Equipment”Cancel Reply
Download Pixel LED Effects 🤩
Pixel LED Effects Download Pack For LEDEdit, NeonPlay, LEDEasy, LEDBuild, Madrix, Jinx, and Glediator.
If you're looking for LED effects, you've come to the right place! Check out our unique animations for LEDEdit and more!
We offer a wide range of animations and effects that are compatible with LEDEdit, the popular LED control software. Our animations are designed to bring life to your LED displays and create stunning visual effects that will capture your audience's attention.
Files: 7000+
Size: 25 GB+
Formats: SWF, TOL, AVI, MP4, and GIF
Our led effects package was created by professionals, and our animations are specially designed for controllers and led programs!
Whether you're looking for simple animations or complex effects, our collection has something for everyone. From colorful transitions and scrolling text to dynamic graphics and mesmerizing patterns, our animations are sure to make your LED displays stand out.
So why wait? Start exploring our collection today and discover the perfect animations for your Pixel LED projects!
This pack contains hundreds of Pixel LED animations for programs that support your LED controller!
All effects in this pack are unique and were created by our team with years of experience in Pixel LED!
Look for a "Buy This Now!" button, click on it to start purchasing, and then download.
How can I pay for Pixel LED Effects Pack?
The payment method for the Pixel LED Effects is through credit or debit cards or PayPal, Your Visa card must be activated for online purchases by your bank.
Are these Pixel LED Effects working with LEDEdit Software?
Yes, Pixel LED Effects is designed to work with the LEDEdit software. LEDEdit is a popular software for programming and controlling LED lights, including pixel LEDs.
Reviews
There are no reviews yet.